EK-FC GeForce GTX FE RGB - Nickel
  • EK-FC GeForce GTX FE RGB - Nickel

EK-FC GeForce GTX FE RGB - Nickel

型番: WBE594

20,489 

(22,128  税込)

在庫切れ

説明

NVIDIA GeForce GTX and Titan X Pascal based graphics cards用水枕

EK-FC GeForce GTX FEはリファレンスデザインのGeForce GTX 1060, GeForce GTX  1070, GeForce GTX  1080, GeForce GTX  1080 Ti, GeForce Titan X Pascal and GeForce Titan Xp based graphics cards等多くのカードに対応しています、お手持ちのカードに対応出来るか否かはEKコンフィギュレーターで確認して下さい。

 

この水枕はSLI時のブロック間接続に専用のEK-FC Terminalが必要です、EK-FC Bridgeは使用できませんのでご注意下さい。


EKの互換性サイトで確認をお願い致します

仕様
Water Block本体: 銅製ベースプレート(ニッケルメッキ仕上)・アクリル樹脂製トップカバー
フィッティングは別売りとなっております
ホース接続口: G1/4

インストレーションマニュアル

VGA用フルカバー ウォーターブロック装着時にご注意下さい
VGA用フルカーバー水枕は各機種ごとに個別に作られていますがリファレンス基盤の標準的な配置を元に製造設計されております。
これは固定ネジの配置や各チップの位置が同じと言うだけでありチップキャパシタやチップレジスターは実際にカードを製造するメーカーによって採用しているパーツが違い高さなどが微妙に異なる可能性がありカードによってはチップパーツが水枕に接触する可能性があります。
従いまして水枕をVGAカードに装着する時には不必要な箇所の接触が無いかを必ず確認して下さい、接触が有る場合はその部分を削る必要がございますので予めご了承下さい

特記事項
EK Waterblocks製Full Cover水枕にてベースプレート側の取り付けねじ穴が緩かったり位置がすれている等の場合は固定ネジを無理にねじ込まないで直ぐに当店へご連絡下さい、 無理にねじ込んだ結果ねじ穴のメッキが剥がれた場合はねじ穴不良のメーカー保証が無くなります(メーカはメッキが剥がれた事で無理にねじ込んだと判断して います、当店でも保証致しかねます)。装着前にまず規定のネジがスムーズにねじ込めるかを確認の後に装着作業を始めて下さいます様お願い致します。

Product EAN: 
3830046995780 

 

EK-FC GeForce GTX FE RGB is a high-performance full-cover water block for multiple NVIDIAR GeForceR GTX and Titan Pascal series graphics cards that comes with pre-installed 4-pin 12V RGB LED strip.
 

Details

EK-FC GeForce GTX FE RGB is a high-performance full-cover water block for multiple NVIDIA® GeForce® GTX and Titan Pascal series graphics cards that comes with pre-installed 4-pin 12V RGB LED strip. 

EK-FC GeForce GTX FE RGB

This water block directly cools the GPU, RAM, and VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it's VRM to remain stable under high overclocks. EK-FC GeForce GTX FE water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps.

This product is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 4-pin LED connector is to be aligned with the +12V marking on the RGB header. You can easily remove the LED strip cover which is mounted with two screws to replace the LED strip with some other type LED strip.

EK RGB All

 

The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. The sealing is ensured by quality rubber O-rings. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure.

EK® recommends the purchase of a retention backplate which improves the aesthetics of your graphics cards, but also provides additional passive cooling to the GPU core and circuit board VRM section. The EK-FC GeForce GTX FE RGB water block is backward compatible with all EK-FC1080 GTX Backplates, EK-FC1080 GTX Ti Backplates, and EK-FC Titan X Pascal Backplates.

G1/4" threaded fittings can be used on both sides of the FC terminal and for multiple GPU connectivity, please refer to our offer of GPU Terminals.

The block also features a special plastic cover over the block Terminal. This add-on is designed to reveal the graphics card model, visible from the side. The terminal cover is removable, it is fitted with 2 screws from the side.

The EK-FC GeForce GTX FE RGB water block is compatible with all reference design GeForce GTX 1060, GeForce GTX  1070, GeForce GTX  1080, GeForce GTX 1080 Ti, GeForce Titan X (Pascal) and GeForce Titan Xp based graphics cards. The current compatibility list rounds up a total of 106 graphics cards that are on the market, but as always, we recommend that you refer to the EK Cooling Configurator for a precise compatibility match.

An additional single-slot I/O bracket can prepurchased separately which replaces the original two-slot in order to make installation of multiple graphics cards easier and also transforms the GPU into a gorgeous single slot solution. The single slot bracket is compatible with reference design NVIDIA® GeForce® GTX 1080 Ti series graphics cards only!

Technical specifications:

- RGB cable length: 30cm
- RGB connector classic 4-pin (12+ R G B)

Enclosed:

- EK-FC GeForce GTX FE RGB series water block
- Mounting mechanism with screw-in brass standoffs
- Necessary mounting screws, nuts, and washers
- 2x EK plug G1/4”
- 6mm Allen key
- Thermal pads
- Thermal grease EK-TIM Ectotherm (1g)

Made in Slovenia - Europe!

PLEASE NOTE:

  • Due to an immense variety of fittings/barbs available on the market and no prescribed standards, we guarantee compatibility only for connectors bought from our website.
  • NVIDIA® GeForce GTX factory backplate is not compatible with this water block!
  • New NVIDIA® SLI HB bridges are compatible with this water block.
  • Check your toolbox if you are missing this special Hex adapter for some of the screws.
  • Fittings are just for showcase and are not included!
  • The optional single slot bracket is compatible with reference design NVIDIA® GeForce® GTX 1080 Ti series graphics cards only!
  • This product should NOT be installed with any aluminum Fluid Gaming parts!

Additional Info

Material / Design / Color option Nickel Plexi
Threads G1/4
Chip Manufacturer Nvidia GeForce

 

追加情報

EK Water Blocks

タグ

添付ファイル

インストールマニュアル (EK-IM-3830046995780.pdf, 825 Kb) [ダウンロード]

友達に知らせる

画像に表示されている英数字を入力してください。



休業日・・・休業日

ロード中...