EK-Vector Radeon VII RGB - Nickel + Plexi
  • EK-Vector Radeon VII RGB - Nickel + Plexi

EK-Vector Radeon VII RGB - Nickel + Plexi w/ Back Plate Black

型番: WBE5008

24,992 

(26,991  税込)

在庫切れ

説明

AMD Radeon VII グラフィックカード専用水枕
ブラックのバックプレートがセットになっています。

EKの互換性サイトで確認をお願い致します

仕様
Water Block本体: 銅製ベースプレート(ニッケルメッキ仕上)・アクリル樹脂製トップカバー
フィッティングは別売りとなっております
ホース接続口: G1/4

VGA用フルカバー ウォーターブロック装着時にご注意下さい
VGA用フルカーバー水枕は各機種ごとに個別に作られていますがリファレンス基盤の標準的な配置を元に製造設計されております。
これは固定ネジの配置や各チップの位置が同じと言うだけでありチップキャパシタやチップレジスターは実際にカードを製造するメーカーによって採用しているパーツが違い高さなどが微妙に異なる可能性がありカードによってはチップパーツが水枕に接触する可能性があります。
従いまして水枕をVGAカードに装着する時には不必要な箇所の接触が無いかを必ず確認して下さい、接触が有る場合はその部分を削る必要がございますので予めご了承下さい

特記事項
EK Waterblocks製Full Cover水枕にてベースプレート側の取り付けねじ穴が緩かったり位置がすれている等の場合は固定ネジを無理にねじ込まないで直ぐに当店へご連絡下さい、 無理にねじ込んだ結果ねじ穴のメッキが剥がれた場合はねじ穴不良のメーカー保証が無くなります(メーカはメッキが剥がれた事で無理にねじ込んだと判断して います、当店でも保証致しかねます)。装着前にまず規定のネジがスムーズにねじ込めるかを確認の後に装着作業を始めて下さいます様お願い致します。

Product EAN: 3831109816158
 
EK-FC Radeon VIIは、複数のAMDRRadeonRVIIグラフィックスカード用の高性能フルカバーウォーターブロックです。詳細な互換性リストについては、当社のCooling Configuratorオンライン互換性システムをチェックしてください。
EK-FC Radeon VII is a high-performance full-cover water block for multiple AMDR RadeonR VII graphics cards. Please check our Cooling Configurator online compatibility system for detailed compatibility list!
 
VectorシリーズのウォーターブロックはEK Quantum Product Lineの一部であり、シンプルでエレガントなデザイン、そしてパフォーマンスを重視しています。目立ちたい人のために!
Vector series water blocks are part of the EK Quantum Product Line that emphasizes minimalistic, elegant design, and performance. For those who want to stand out!
 

Details

 

EK-FC Radeon VII is a high-performance full-cover water block for multiple AMD® Radeon® VII graphics cards. Please check our Cooling Configurator online compatibility system for detailed compatibility list!

This water block directly cools the GPU, 16GB of HBM2 memory, and VRM (voltage regulation module) as cooling liquid is channeled directly over these critical areas. These newly developed water blocks feature a redesigned cooling engine that has a larger footprint compared to the previous generation of EK® Full Cover water blocks. This results in a larger surface area for heat transfer which increases the thermal performance of these water blocks. 

EK-Vector Radeon VII

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed water flow scenarios. 

The base of the block is made of nickel-plated electrolytic copper while the top is made of high-quality acrylic material. Sealing is ensured by high-quality EPDM O-Rings. The brass standoffs are already pre-installed and allow for a safe and easy installation procedure. The front aesthetic corner piece is lit up with LED strip.

Vector RGB Compatibility

This product is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 4-pin LED connector is to be aligned with the +12V marking on the RGB header. 

EKWB recommends the purchase of aesthetic retention backplate which improves the looks of your graphics cards and also provides some passive cooling to the circuit board VRM section. The EK-FC Radeon VII water block is compatible with both Nickel and Black versions of the EK-FC Radeon VII Backplates.

EK-Vector Radeon VII Single slot

EK also encloses a single-slot I/O bracket which replaces the original two-slot in order to make installation of multiple graphics cards easier and also transforms the GPU into a gorgeous single slot solution.

G1/4" threaded fittings can be used on both sides of the FC terminal.

Reviewed by:

EK-Vector Radeon VII Recommended Review

Enclosed:
- EK-FC Radeon VII series water block
- Mounting mechanism with screw-in brass standoffs
- Necessary mounting screws, nuts, and washers
- 2x EK plug G1/4”
- 6mm Allen key
- Thermal pads
- Thermal grease EK-TIM Ectotherm (1g)

Made in Slovenia - Europe!

PLEASE NOTE:

  • Due to an immense variety of fittings/barbs available on the market and no prescribed standards, we guarantee
    compatibility only for connectors bought from our website.

  • Fittings are just for showcase and are not included!
  • This product should NOT be installed with any aluminum Fluid Gaming parts!
  • Radeon VII stock backplates are compatible with EK-Vector Radeon VII water blocks only if installed with the stock backplate screws. For the best performance and aesthetics, EK recommends using the EK-Vector Radeon VII Backplates instead.

Additional Info

 

Material / Design / Color option

Nickel Plexi
Threads G1/4
Chip Manufacturer AMD Radeon

 

EK-Vector Radeon VII Backplate - Black

Details

EK-Vector Radeon VII Backplate is a CNC machined retention backplate made from black anodized aluminum for EK-Vector Radeon VII series water blocks.

Backplate covers the whole length of graphics cards PCB, serves as an aesthetic add-on and also provides passive cooling for the backside of voltage regulation module (VRM).

This backplate is guaranteed to be compatible with reference PCB AMD® Radeon® VII graphics cards.

Enclosed:
- EK-Vector Radeon VII Backplate - Black
- Mounting mechanism
- Thermal pads

Made in Slovenia - Europe!

PLEASE NOTE:

  • Please check both ends of the packaging box for the enclosed mounting screws!
  • The backplate does not serve as a standalone unit and is compatible with EK-Vector Radeon VII water blocks!
  • Check your toolbox if you are missing this special Hex adapter for some of the screws.

追加情報

EK Water Blocks

タグ

添付ファイル

インストレーションマニュアル (EK-IM-3831109816158.pdf, 1,588 Kb) [ダウンロード]

友達に知らせる

画像に表示されている英数字を入力してください。



休業日・・・休業日

ロード中...