EK Vector RTX Titan - Acetal + Gold
  • EK Vector RTX Titan - Acetal + Gold

EK Vector RTX Titan - Acetal + Gold

型番: WBE5009

32,636 

(35,247  税込)
2 個

説明

NVIDIA TITAN RTX グラフィックカード専用水

 

この水枕はSLI時のブロック間接続に専用のEK-FC Terminalが必要です、EK-FC Bridgeは使用できませんのでご注意下さい。


EKの互換性サイトで確認をお願い致します

仕様
Water Block本体: 銅製ベースプレート(ニッケルメッキ仕上)・アクリル樹脂製トップカバー
フィッティングは別売りとなっております
ホース接続口: G1/4

VGA用フルカバー ウォーターブロック装着時にご注意下さい
VGA用フルカーバー水枕は各機種ごとに個別に作られていますがリファレンス基盤の標準的な配置を元に製造設計されております。
これは固定ネジの配置や各チップの位置が同じと言うだけでありチップキャパシタやチップレジスターは実際にカードを製造するメーカーによって採用しているパーツが違い高さなどが微妙に異なる可能性がありカードによってはチップパーツが水枕に接触する可能性があります。
従いまして水枕をVGAカードに装着する時には不必要な箇所の接触が無いかを必ず確認して下さい、接触が有る場合はその部分を削る必要がございますので予めご了承下さい

特記事項
EK Waterblocks製Full Cover水枕にてベースプレート側の取り付けねじ穴が緩かったり位置がすれている等の場合は固定ネジを無理にねじ込まないで直ぐに当店へご連絡下さい、 無理にねじ込んだ結果ねじ穴のメッキが剥がれた場合はねじ穴不良のメーカー保証が無くなります(メーカはメッキが剥がれた事で無理にねじ込んだと判断して います、当店でも保証致しかねます)。装着前にまず規定のネジがスムーズにねじ込めるかを確認の後に装着作業を始めて下さいます様お願い致します。

Product EAN: 3831109815892
 
The EK-Vector RTX Titan is a special edition run of the full cover EK-Vector series GPU water block. The EK-Vector RTX Titan is aesthetically designed for the best fit with NVIDIA TITAN RTX high-performance graphics cards. It features a performance tweaked a gold plated cold plate, acetal top cover, gold plated screws, and a special RGB lit gold plated aesthetic end piece.  
 

 

Vector series water blocks are part of the EK Quantum Product Line that emphasizes minimalistic, elegant design, and performance. For those who want to stand out!
 

Details

The EK-Vector RTX Titan is a special edition run of the full cover EK-Vector series GPU water block. The EK-Vector RTX Titan is aesthetically designed for the best fit with NVIDIA® RTX Titan ™ high-performance graphics cards. It features a performance tweaked gold plated cold plate, acetal top cover, gold plated screws, and a special RGB lit gold plated aesthetic end piece.

EK Vector TITAN RTX

The EK-Vector RTX Titan also fits multiple NVIDIA® GeForce® RTX 2080 Ti graphics cards. The water block itself uses the signature EK®single slot slim look, and it covers the entire PCB length. This sophisticated cooling solution will transform your beefy graphics card into a minimalistic, elegant piece of hardware. The block also features a unique aesthetic cover over the block Terminal which is designed to reveal the graphics card model, visible from the side.

The water block directly cools the GPU, VRAM and the VRM (voltage regulation module) as cooling liquid is channeled directly over these critical areas. This special edition water block features a redesigned cooling engine that has a larger footprint compared to the previous generation of EK® Full Cover water blocks. This results in a larger surface area for heat transfer which increases the thermal performance of these water blocks. 

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed water flow scenarios. 

RGB compatibility

The base of the block is CNC machined out of gold plated electrolytic copper while the top is CNC machined out of black POM acetal material. Sealing is ensured by high-quality EPDM O-Rings. The brass standoffs are already pre-installed and allow for a safe and easy installation procedure. The front aesthetic corner piece is lit up with a special LED light diffuser. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 4-pin LED connector is to be aligned with the +12V marking on the RGB header. 

EK® recommends the purchase of a retention backplate which improves the aesthetics of your graphics cards, but also provides additional passive cooling to the GPU core and circuit board VRM section.

G1/4" threaded fittings can be used on both sides of the terminal and for multiple GPU connectivity, please refer to our offer of GPU Terminals. The EK-Vector GPU water block terminal cover is not compatible with FC Terminal X and FC Terminal (Legacy) multi GPU connectivity bridges.

The NVIDIA® NVLink is compatible with this water block. 

Enclosed:

- EK-Vector special edition high-performance water block
- Mounting mechanism with screw-in brass standoffs
- Necessary mounting screws, nuts, and washers
- 2x Nickel plated brass plug G1/4”
- 6mm Allen key
- Thermal pads
- Thermal grease EK-TIM Ectotherm (1g)

Made in Slovenia - Europe!

PLEASE NOTE:

  • TO PREVENT DAMAGE TO YOUR WATER BLOCK, YOUR COOLANT MUST CONTAIN ANTICORROSIVES AND BIOCIDES! EK RECOMMENDS USE OF EK CRYOFUEL COOLANTS.
  • Due to an immense variety of fittings/barbs available on the market and no prescribed standards, we guarantee compatibility only for connectors bought from our website.
  • NVIDIA® RTX 2080Ti Founders edition factory backplate is not compatible with this water block!
  • Check your toolbox if you are missing this special Hex adapter for some of the screws.
  • Fittings are just for showcase and are not included!
  • The EK-Vector GPU water block terminal cover is not compatible with FC Terminal X and FC Terminal (Legacy) multi GPU connectivity bridges.
  • This product should NOT be installed with any aluminum Fluid Gaming parts!

Additional Info

Threads G1/4
Chip Manufacturer Nvidia GeForce

 

追加情報

EK Water Blocks

タグ

添付ファイル

インストレーションマニュアル (EK-IM-3831109815892.pdf, 1,620 Kb) [ダウンロード]

友達に知らせる

画像に表示されている英数字を入力してください。



休業日・・・休業日

ロード中...