EK-Vector Aorus RTX 2080 Ti RGB - Nickel + Plexi  w/ Back Plate Nickel
  • EK-Vector Aorus RTX 2080 Ti RGB - Nickel + Plexi  w/ Back Plate Nickel

EK-Vector Aorus RTX 2080 Ti RGB - Nickel + Plexi w/ Back Plate Nickel

型番: WBE5015

26,628 

(28,758  税込)
3 個

説明

Gigabyte Aorus version of NVIDIAR GeForceR RTX 2080 Ti グラフィックカード専用水枕
ニッケルのバックプレートがセットになっています。

EKの互換性サイトで確認をお願い致します

仕様
Water Block本体: 銅製ベースプレート(ニッケルメッキ仕上)・アクリル樹脂製トップカバー
フィッティングは別売りとなっております
ホース接続口: G1/4

VGA用フルカバー ウォーターブロック装着時にご注意下さい
VGA用フルカーバー水枕は各機種ごとに個別に作られていますがリファレンス基盤の標準的な配置を元に製造設計されております。
これは固定ネジの配置や各チップの位置が同じと言うだけでありチップキャパシタやチップレジスターは実際にカードを製造するメーカーによって採用しているパーツが違い高さなどが微妙に異なる可能性がありカードによってはチップパーツが水枕に接触する可能性があります。
従いまして水枕をVGAカードに装着する時には不必要な箇所の接触が無いかを必ず確認して下さい、接触が有る場合はその部分を削る必要がございますので予めご了承下さい

特記事項
EK Waterblocks製Full Cover水枕にてベースプレート側の取り付けねじ穴が緩かったり位置がすれている等の場合は固定ネジを無理にねじ込まないで直ぐに当店へご連絡下さい、 無理にねじ込んだ結果ねじ穴のメッキが剥がれた場合はねじ穴不良のメーカー保証が無くなります(メーカはメッキが剥がれた事で無理にねじ込んだと判断して います、当店でも保証致しかねます)。装着前にまず規定のネジがスムーズにねじ込めるかを確認の後に装着作業を始めて下さいます様お願い致します。

Product EAN: 3831109814710
 
The EK-Vector Aorus RTX 2080 Ti RGB high-performance water block is specially designed for Gigabyte AorusR version of NVIDIAR GeForceR RTX 2080 Ti graphics cards. The water block itself uses the signature EKR single slot slim look, and it covers the entire PCB length. This sophisticated cooling solution will transform your powerful Gigabyte graphics card into a minimalistic, elegant piece of hardware with accented RGB LED lighting.
 
EKR Quantum - Design & Performance 
 
Vector series water blocks are part of the EK Quantum Product Line that emphasizes minimalistic, elegant design, and performance. For those who want to stand out!
 

Details

The EK-Vector Aorus RTX 2080 Ti RGB high-performance water block is specially designed for Gigabyte Aorus® version of NVIDIA® GeForce® RTX 2080 Ti graphics cards. The water block itself uses the signature EK® single slot slim look, and it covers the entire PCB length. This sophisticated cooling solution will transform your powerful Gigabyte graphics card into a minimalistic, elegant piece of hardware with accented RGB LED lighting. The block also features a unique aesthetic cover over the block Terminal which is designed to showcase the graphics card model via LEDs, visible from the side.

This water block is compatible with all Gigabyte Aorus® GeForce RTX 2080 Ti graphics cards, but as always, we recommend that you refer to the EK® Cooling Configurator for a precise compatibility match. 

The water block directly cools the GPU, VRAM and the VRM (voltage regulation module) as cooling liquid is channeled directly over these critical areas. These newly developed water blocks feature a redesigned cooling engine that has a larger footprint compared to the previous generation of EK® Full Cover water blocks. This results in a larger surface area for heat transfer which increases the thermal performance of these water blocks. 

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed water flow scenarios. 

The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. Sealing is ensured by high-quality EPDM O-rings. The brass standoffs are already pre-installed and allow for a safe and easy installation procedure. It features four integrated LED sources, two located in the terminal cover and one LED strip on each end of the water block.

The block is already equipped with 4 12V RGB LED strip which is compatible with the motherboard 4-pin 12V RGB LED header. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers.

 RGB compatibility

EK® recommends the purchase of a retention backplate which improves the aesthetics of your graphics cards, but also provides additional passive cooling to the GPU core and circuit board VRM section.

G1/4" threaded fittings can be used on both sides of the terminal and for multiple GPU connectivity, please refer to our offer of GPU Terminals

Both the NVIDIA® and Gigabyte NVLink™ are compatible with this water block. 

Enclosed:

- EK-Vector Aorus series high-performance water block
- Mounting mechanism with screw-in brass standoffs
- Necessary mounting screws, nuts, and washers
- 2x Nickel plated brass plug G1/4”
- 6mm Allen key
- Thermal pads
- Thermal grease EK-TIM Ectotherm (1g)

Made in Slovenia - Europe!

PLEASE NOTE:

  • Due to an immense variety of fittings/barbs available on the market and no prescribed standards, we guarantee compatibility only for connectors bought from our website.
  • Gigabyte Aorus® RTX 2080Ti factory backplate is not compatible with this water block!
  • Check your toolbox if you are missing this special Hex adapter for some of the screws.
  • Fittings are just for showcase and are not included!
  • This product should NOT be installed with any aluminum Fluid Gaming parts!
  • The use of specifically engineered coolants that contain corrosion, scale, and biological inhibitors is mandatory to prevent damage to your nickel plated water block! EK is offering a selection of such products in the coolants section.

Additional Info

Material / Design / Color option Nickel Plexi
Threads G1/4
Chip Manufacturer Nvidia GeForce

 

EK-Vector Aorus RTX 2080 Ti Backplate - Nickel

Product EAN: 3831109817087
 
 
EK-Vector Aorus RTX 2080 Ti Backplate - Nickel is a CNC machined retention backplate made from nickel plated aluminum, that fits all EK-Vector Aorus RTX 2080 Ti water blocks.
 
EKR Quantum - Design & Performance 
 
Vector series backplates are part of the EK Quantum Product Line that emphasizes minimalistic, elegant design, and performance. For those who want to stand out!
 

Details

EK-Vector Aorus RTX 2080 Ti Backplate - Nickel is a CNC machined retention backplate made from nickel plated aluminum, that fits all EK-Vector Aorus RTX 2080 Ti water blocks.

Backplate covers the whole length of graphics cards PCB, serves as an aesthetic add-on and also provides passive cooling for the backside of the voltage regulation module (VRM) and the GPU core.

This backplate is guaranteed to be compatible with all Gigabyte Aorus® RTX 2080 Ti graphics cards.

Enclosed:
- EK-Vector Aorus RTX 2080 Ti Backplate - Nickel
- Mounting mechanism
- Thermal pads

Made in Slovenia - Europe!

Additional Info

Chip Manufacturer Nvidia GeForce

 

追加情報

EK Water Blocks

タグ

添付ファイル

インストレーションマニュアル (EK-IM-3831109814710.pdf, 795 Kb) [ダウンロード]

インストレーションマニュアル-バックプレート (EK-IM-3831109817070.pdf, 453 Kb) [ダウンロード]

友達に知らせる

画像に表示されている英数字を入力してください。



休業日・・・休業日

ロード中...