EK-Quantum Vector Strix RX 5700 +XT DRGB - Nickel + Plexi
  • EK-Quantum Vector Strix RX 5700 +XT DRGB - Nickel + Plexi

EK-Quantum Vector Strix RX 5700 +XT DRGB - Nickel + Plexi

型番: WBE5018

19,056 

(20,962  税込)
2 個

説明

ASUS ROG Strix version of AMDR RadeonR RX 5700 and RX 5700 XTグラフィックカード専用水


EKの互換性サイトで確認をお願い致します

仕様
Water Block本体: 銅製ベースプレート(ニッケルメッキ仕上)・アクリル樹脂製トップカバー
フィッティングは別売りとなっております
ホース接続口: G1/4

VGA用フルカバー ウォーターブロック装着時にご注意下さい
VGA用フルカーバー水枕は各機種ごとに個別に作られていますがリファレンス基盤の標準的な配置を元に製造設計されております。
これは固定ネジの配置や各チップの位置が同じと言うだけでありチップキャパシタやチップレジスターは実際にカードを製造するメーカーによって採用しているパーツが違い高さなどが微妙に異なる可能性がありカードによってはチップパーツが水枕に接触する可能性があります。
従いまして水枕をVGAカードに装着する時には不必要な箇所の接触が無いかを必ず確認して下さい、接触が有る場合はその部分を削る必要がございますので予めご了承下さい

特記事項
EK Waterblocks製Full Cover水枕にてベースプレート側の取り付けねじ穴が緩かったり位置がすれている等の場合は固定ネジを無理にねじ込まないで直ぐに当店へご連絡下さい、 無理にねじ込んだ結果ねじ穴のメッキが剥がれた場合はねじ穴不良のメーカー保証が無くなります(メーカはメッキが剥がれた事で無理にねじ込んだと判断して います、当店でも保証致しかねます)。装着前にまず規定のネジがスムーズにねじ込めるかを確認の後に装着作業を始めて下さいます様お願い致します。

Product EAN:3831109822180
 

Details

The EK-Quantum Vector Strix RX 5700 +XT D-RGB high-performance water block is specially designed for the ROG® Strix version of AMD® Radeon® RX 5700 and RX 5700 XT graphics cards. The water block itself uses the signature EK® single slot slim look, and it covers the entire PCB length. This sophisticated cooling solution will transform your powerful ROG graphics card into a minimalistic, elegant piece of hardware with accented addressable D-RGB LED lighting.

Cooling is directed at the GPU, 8GB of GDDR6 memory, and VRM (voltage regulation module) as cooling liquid is channeled directly over these critical areas. These newly developed Vector water blocks feature a redesigned cooling engine that has a larger footprint compared to the previous generation of EK® Full Cover water blocks. This results in a larger surface area for heat transfer which increases the thermal performance of these water blocks.

EK-Quantum Vector Strix RX 5700 XT

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed water flow scenarios. 

The base of the block is made of nickel-plated electrolytic copper while the top is made of high-quality acrylic material. Sealing is ensured by high-quality EPDM O-Rings. The brass standoffs are already pre-installed and allow for a safe and easy installation procedure.

The block is already equipped with 3-pin 5V Addressable D-RGB LED strip which is compatible with the motherboard 3-pin 5V Addressable D-RGB LED header. This product is also compatible with popular RGB sync technologies from all major motherboard manufacturers which support the pinout: +5V, D, Blocked, Ground. The arrow marking on the 3-pin LED connector is to be aligned with the +5V marking on the addressable gen2 LED header (ADD GEN2_1 and ADD GEN2_2 marked headers).

 ASUS Aura Sync

EKWB recommends the purchase of aesthetic retention backplate which improves the looks of your graphics cards and also provides some passive cooling to the circuit board VRM section. The EK-Quantum Vector Strix RX 5700 +XT D-RGB water block is compatible with both Nickel and Black versions of the EK-Quantum Vector Strix RX 5700 +XT Backplates.

EK-Quantum Vector Radeon RX 5700 +XT D-RGB

G1/4" threaded fittings can be used on both sides of the terminal and for multiple GPU connectivity, please refer to our offer of EK-Scalar GPU Terminals. The EK-Quantum Vector RX GPU water block terminal cover is not compatible with FC Terminal X and FC Terminal (Legacy) multi GPU connectivity bridges.

Enclosed:
EK-Quantum Vector Strix RX 5700 +XT series water block
- Mounting mechanism with screw-in brass standoffs
- Necessary mounting screws, nuts, and washers
- 2x EK plug G1/4”
- 6mm Allen key
- Thermal pads
- Thermal grease EK-TIM Ectotherm (1g)

Made in Slovenia - Europe!

PLEASE NOTE:

  • Due to an immense variety of fittings/barbs available on the market and no prescribed standards, we guarantee
    compatibility only for connectors bought from our website.
  • The ROG Strix Radeon™ RX 5700 XT factory backplate is compatible with this water block only if the stock thermal pads are removed!
  • Fittings are just for showcase and are not included!
  • This product should NOT be installed with any aluminum Fluid Gaming parts!
  • The use of specifically engineered coolants that contain corrosion, scale, and biological inhibitors is mandatory to prevent damage to your nickel plated water block! EK is offering a selection of such products in the coolants section.

Additional Info

Material / Design / Color option Nickel Acetal
Threads G1/4
Sockets AMD

 

追加情報

EK Water Blocks

タグ

添付ファイル

インストレーションマニュアル (EK-IM-3831109822180.pdf, 1,089 Kb) [ダウンロード]

友達に知らせる

画像に表示されている英数字を入力してください。



休業日・・・休業日

ロード中...